Well, we all have gauges of some sort on our vehicle that tell us the REALLY important things like “You’re Outta Gas!” or “I’m getting too hot!“, but there’s a lot more information that all our newer (since 1996 or so) vehicles have that can be extracted from the on board computer (known as the Engine Control Module) and, if you have the right device, then display that data on a screen so the driver can see and monitor the engine load and performance. On diesel trucks and motorhomes, this data is sent by the ECM to a “Deutsch” connector. On pick-up trucks and passenger cars they use an OBDII (On-Board Diagnostic) connector.
One such device for diesel engines in Motorhomes is BLUEFIRE FOR MOTORHOMES.
I discovered this device and it’s associated app while visiting the Quartzsite “Big Tent” RV show in January of 2019. Their display of the user interface caught my eye and so I went over and talked to Mark Fredrickson who, as it turns out is the developer of both the plug-in adapter and the free app available for Apple, Android devices and Windows 10 computers.
This device (called the adapter) plugs into your diesel vehicle Deutsch Connector. In our case, there is a round 6-pin Deutsch connector mounted just inside the rear “hood” of our coach just over the top of the radiator (labeled Diagnostics). There is another duplicate connector mounted under the dash. These are the connectors that the mechanic would use for diagnostic purposes.
This is what our (6 pin) adapter looks like
The really sweet thing about Bluefire for Motorhomes is that the adapter is BLUETOOTH which means the adapter talks to your phone/tablet/laptop wirelessly and this means that you don’t have to deal with any unsightly wires coming out from under the dash AND you don’t need to provide any power to the adapter since it gets it’s own power from the Deutsch connector.
The BlueFire for Motorhomes App is free and can be downloaded and installed from Apple Tunes, Google Play, or the Microsoft App Stores. It will run completely in Demo mode so you can get a feel for it’s capabilities before purchasing an Adapter.
The cost of the adapter starts at $150.00 (for a 6 pin Android/Windows adapter) up to $190.00 for the 9 pin (newer motorhomes) Android/Windows/Apple adapter. You will need to look at your Deutsch connector to see if it’s 6 or 9 pin and also decide what platform you are going to run it on (Apple/Android/Microsoft).
If you need to use Bluefire on a pickup truck or other vehicle with an OBDII connector, then order the appropriate adapter from the link in the box below.
Since our motorhome is a 2002 Airstream on a Freightliner chassis with a CAT 3126 engine and a 6 pin Deutsch, we were able to purchase our adapter for $150.00
Since the app is FREE, I urge you to download the app and play with it in DEMO mode. This will allow you to learn about all the various settings and learn about how you might want your “dashboard” to look like. To use the app in DEMO mode, from the main menu (or control panel) click on SETTINGS & then UN-check DO NOT SHOW DEFAULT DATA.
Your custom dashboard is completely customize-able. You select which gauges you want displayed, what style the gauge will be (circular, text, or linear), what colors you want, and all gauge placement. Here’s a shot of how I set up my dash for our motorhome.
You can see that I have 8 circular gauges, 8 text gauges, and 3 buttons on my dash. And I still have room on the screen to add more. I can even place a dynamic map on the dashboard that works off the GPS.
This is the tablet I’m using for Bluefire. My laptop was too big. I would have to set it on the dash and then I couldn’t reach it from the driving position. My Android phone is too small and it mounts on a long flexible neck that tends to bounce around during travel. This would make it too had to view the gauges, so the 8′ tablet was the way to go for me.
Here’s the base that I bought to mount the tablet. I screwed the mount right into the dash just to the left of the back-up monitor left of the steering wheel. It’s a very solid mount and does not allow the tablet to jiggle or bounce around as you travel down the road.
In the screenshots below you will see just how many parameters there are that the ECM sends to Bluefire and you can make gauges on your custom dashboard displaying ANY of these parameters.
Be aware that not ALL motorhomes ECM’s will transmit ALL of these parameters. My coach is an older (2002) and there are a few pieces of data that just don’t come across (like coolant LEVEL) because my coach doesn’t have a sensor that feeds into the ECM for that.
I DO however have a LOW WATER light and buzzer on the Freightliner dash that warns me … which by the way I found DOES work as we were climbing a steep hill, the coolant in the reservoir shifted to the back thereby exposing the sensor and setting off our LOW WATER alarm!
It’s very easy to operate. Here’s how I turn it on and start to use the system.
Turn on my tablet, enable Bluetooth and open the Bluefire app. I have my settings set to NOT bring up default values when not connected (ignition off). Start the engine. Push CONNECT on the app control panel. Push “TRIPS” on app control panel and enter the name of my trip that I’m starting. Push START TRIP. Push one of 3 buttons on Control Panel (either DASHBOARD, DRIVE, or REPAIR) to view graphical data being sent from the ECM.
DRIVE and REPAIR each have multiple screens (you can scroll up and down) that show you every possible parameter that your ECM might be sending to the adapter.
Using the TRIP function all the driver has to do is start and connect the app to the adapter, enter the name of the trip, (i.e. Chicago to St. Louis) and then push START TRIP. The app and the ECM do the rest of the work. When you stop for fuel, push FUEL FILL-UP – the app will ask you if it’s a total or partial fill. At the end of the trip push STOP TRIP and you’ll see the results on-screen and a report will be emailed in a csv spreadsheet format. The spreadsheet is amended with another ROW after each trip so all your trip(s) data is automatically saved in a nice compact format for easy retrieval at any time in the future.
Here is the link to purchase the Bluefire For Motorhomes Adapter from our Amazon Associates Page. If you order from Amazon (through this link) or the BUY NOW button below, then we will be paid a small fee from Amazon and the purchase doesn’t cost you any more.
Here’s a link to their Getting Started Document that’s 23 pages long and really explains a lot. I don’t think this document was available when I started using Bluefire or maybe I just never saw it — I learned by experimenting.
For a quick look at some of the App pages follow this link to the Bluefire web site.
If you’re not already subscribed to this blog, you can easily do so by scrolling up to the top of any page and entering your email address in the block on the right side.
You can also subscribe to our YouTube channel (herbnkathyrv) on You Tube.
If you’re curious (at any time) to know where we are at that moment then click the button at the top right of this page labeled “See Where We Are Now“.
Any questions, I’ll be glad to answer them as best I can. Please put questions and comments in the comment section below rather than email so that others can benefit from our conversation as well.
We’d love to hear from you. If you scroll all the way down to the bottom of this page, you can send us a note. Again, thanks for riding along. ’til next time – safe travels.